An Easy Instruction for Installing a Bathtub
An Easy Instruction for Installing a Bathtub
Blog Article
How do you really feel about A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably tough job. If the old tub is easily accessible, the task can relocate quickly; if you need to open up a wall to remove the old tub as well as place the brand-new bathtub, the job is much harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. See to it you have actually certified yourself for the job and also fit trying it. Rather than working with a service provider to take over a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will help you install a brand-new tub in your shower room if you have currently acquired a new bathtub and don't require to transform the plan of your previous supply of water pipes.
Your tools and material list must comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is disconnect the water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. When the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to going on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the faucet and the sink. Secure the tap in place with the producer offered backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The former kind should be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are handy in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub till the level reads level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the tub as well as additionally examine the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait up until the tub has been utilized a minimum of when as this will resolve it into its last position.
Getting ready for the Installation
Firstly, the supporting structure provided with the bath ought to be fitted (if needed) according to the maker's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to avoid strain on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, causing issues with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and also installations. They are sold in tubes as well as cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealer can fracture relatively early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very taken with Tools You Need to Install a New Bathtub and I'm hoping you appreciated our post. Are you aware of somebody who is excited by the niche? Please feel free to share it. Thanks a bunch for your time. Please come visit our blog back soon.
Top service? Dial now. Report this page